Joytech Cuboid Tap Kit Review | Blogspot

Full disclosure:

Let’s get all the disclosures out of the way. This kit was sent to me directly from Joytech specifically for the gain of this review. This will not in any manner, shape, or form cause ME to provide this kit a positive review or modify my opinion in any method. As always you can get a good and honest review.

First Impression Out Of The Box:

Nice looking mod. Has a carbon fiber look with some kind of glossy covering. Has a dark grey and black colour scheme to that. Smooth in the hand and amazingly little for a twin 18650 mod. Packaged below the 1st layer within the box is that the professional Core Aries tank. Good wanting 2 tone tank. Looks nice on the Cuboid TAP.

What's In The Box:

* 1 x Joye Cuboid TAP
* 1 x Joye ProCore Aries
* 1 x ProC1 zero.4ohm Atomizer Head
* 1 x ProC4 zero.15ohm Octuple Coil atomiser Head
* 1 x Replacement Glass
* 1 x QC USB Cable
* 1 x Set of Spare components

The Mod:


As usual let's start with the 510. Looks like a similar 510 as Wismec Predator. I put them next to every different and that they do so look identical in each manner. The 510 pin is spring loaded and it actually has a nice throw to that. Before everyone gets defensive, I did do a pull test. I put a tank on it and rocked it back and forth and gave it some sensible pulls and also the 510 did delay. I used way a lot of force than one would once pull a prime of AN RDA off. So so much thus nice. The 510 itself has stainless steel threading and also the pin is gold plated. So so much each atty I actually have placed on it works and a lot of significantly all of them sit nice and flush.

This is a really small mod for a twin 18650 mod. Even smaller than my IPV Vesta. Not by much however it is so smaller. The body of the mod is covered in a very shiny carbon fiber wanting material. It’s smooth and feels nice in the hand. There is no actual branding on the mod itself aside from the highest across from the 510 there's some black on black writing that says Joytech Cuboid TAP. You really do need to look to check it.


Next we have one among the 2 firing buttons. Yes I told 2 firing buttons. The first one may be a trad firing button on a similar part of the mod as 510. Located   below the 510 the standard firing button is black and sq.. It is clicky but contains a longer throw than most mods in its category. It almost has a mushy feel to that however in my opinion it stops simply short of really being mushy. The other firing button is found JUST higher than the screen of the mod. It is a taptic type button that seems like slightly sensitive plate. Joytech calls it taptech technology. It’s about 3 times the dimensions of the standard one and it provides off some perception feedback once pressed  that's quite the same as the feedback or abuzz you get from a smartphone. It is comfortable and responsive. It can additionally be turned off within the menu system. Since there's only 1 real button on this mod there is no button rattle in any respect.

Below the taptech firing button is the screen. It is big lovely and bright however to my dismay it doesn't act good in direct daylight. Every different lighting condition this screen is Very simple to browse. In standby mode the screen shows a clock. In temp mode it shows the material, resistance, puf/time/amps, temperature, mode, and battery meter. Inpower mode it shows the mode, resistance, puf/time/amps, watts, volts, and battery meter.

Under the screen is wherever the taptic +/- buttons ar. They provide perception feedback once pushed and that they do take some obtaining used too. They are wont to regulate the power and temperature also on toggle between menu choices. Right below the +/- buttons you have the usb port. It is used for charging and updates. The Cuboid Tap will have two amp charging however I do extremely suggest that everybody charge their batteries outwardly. Definitely a nice feature to own for once you ar in pinch.

The battery door is well done on this mod. Pull out and up to open it and pull out and push down and in too close it. No battery rattle and everything sits in there very solidly. There are battery orientation markings within the mod and on the back of the battery door. The battery contacts on the door are gold plated. Even when the door is open there is not plenty of play or wiggle in it. There is some venting on the battery door.

The Tank:

This kit comes with a Pro Core Aries tank and 2 coils. The TOP cap is hinged and sort of reminds of the Sense blaser top cap. It flips open like a wc seat. There are 2 juice ports on either side of this TOP fill tank. There is also a rubber seal however I didn't see a spare ones in my kit. The drip tip is delrin with a metal interior. You cannot use your own drip recommendations on this tank. To open the Aries you look for the Aries symbol on the sting of top cap. Once located, push away from the symbol and also the TOP cap slide out and flips up.

The Aries uses pyrex glass and has a conically designed barrel that flows into a narrower chimney. The base screws off and divulges your coil. The base is secured to the glass by screwing top of the coil into the chimney. A beefy oring at the base protects against any leaky. The base has dual adjustable air flow. It has stoppers on either side and therefore the air flow is incredibly sleek. Threading on the tank is overall very sensible.

You get two coils with this kit. One is the ProC1 0.4ohm Dual Coil atomiser Head for Direct respiratory organ (DL) that has a suggested electrical power of forty - 80W. The other is that the ProC4 zero.15ohm Octuple Coil atomiser Head for Direct respiratory organ (DL) with counseled electrical power of fifty - 110W. Both coils ar nice however I do like the .4 ohm. These coils are compatible with the Baby Beast by Smok and their coils can match the Aries.
The Look, Feel, and General Aesthetics Of The Mod And Tank:

* The Mod:

I love the design and feel of this mod. From the carbon fiber look to the smooth texture it simply feels very solid on your hand. I like the taptic firing button. I find it comfy to fireplace the mod this manner with my thumb. The traditional firing button is incredibly comfy to trigger finger fireplace further. I would prefer to caution people concerning exploitation the taptic firing button. Make certain if you're not exploitation it or if you're putt it in a very pocket or purse you either flip the button or the mod itself off. The reason being is any form of pressure on it button will so fireplace that mod. The firing plate does tend to get hot once chain vaping.

I love the New Look and feel of this mod but with innovation comes a brand new set of issues as a result of this sort of switch isn't what folks ar accustomed. That’s why I wrote about closing the mod off or the button off once carrying the mod. While I do like the taptic button it will present a brand new reasonably issue for the user. I do like the way it works however i'll tell my readers to use caution once exploitation it. The mod comes in 5 colours, silver, black, red, yellow, and blue. I love the design of the black one they sent me. I’m glad I got that one because the red, yellow, and blue all have a gaudy type of graphic on the Side of the mod. Kind of a shame because base color of these mods ar very bright and vivacious I’m simply not a lover of the graphics they used. Besides the black the only different one i'd in person purchase is that the silver.

* The Tank:

Love the two tone look of this tank. I think black and stainless-steel look nice along. Really sleek draw and well created. All the machining is very nice. The tank appearance nice and vapes as nice as it looks.


The Board:

Typical Joytech board, nothing new it's the same board because the Evic Primo Mini. This mod has a full temperature control suite also as three presets for TCR and a bypass mode. It will FIRE from one - 228 watts and also the temperature may be set from two hundred - 600 degrees Fahrenheit. In TC it will fireplace as low as .05 ohms and in wattage mode it can fireplace as low as .1 ohm. For me whenever I vaped this board in TC if my build was below .2 ohms it kicked American state out of TC and into electrical power mode. Hopefully Joytech fixes this with an update. When I used it in SS mode higher than .2 ohms the TC was on purpose. TCR was very great also.